| 화면 아이콘 | 코드 | 내용 |
|---|---|---|
 | 300 | FPGA 에러FPGA error Occurs if FPGA is not functioning properly. |
 | 301 | 본체 CPU 내부 RAM 에러Main unit CPU internal RAM error Displayed when a malfunction occurs in the CPU's internal RAM, in the main unit. |
 | 302 | 본체 CPU 내부 FROM 에러Main unit CPU internal FROM error Occurs when the checksum value in the CPU's internal FROM does not match the calculated checksum value, in the main unit. |
 | 303 | 본체 부동소수점 0으로 나누기 에러Main unit floating decimal division by zero error Displayed when division by zero occurs during floating point calculations in the main unit or if an invalid calculation occurs. |
 | 304 | 본체 외부 RAM 에러Main unit external RAM error 에 오작동 발생 본체 외부 RAM일 때 표시됨 |
 | 305 | 본체 외부 FROM 에러Main unit external FROM error Displayed when a checksum value in the main unit external FROM does not match the calculated checksum value. |
 | 306 | EEPROM에 아웃리거 사양 미설정Outrigger specifications not specified in EEPROM Occurs when replacing circuit boards. |
 | 307 | 아웃리거 사양 용 DIP 스위치 상 회로 board이(가) 아웃리거 사양 내 EEPROM와 불일치Outrigger specifications for DIP switches on circuit board does not agree with outrigger specifications in EEPROM Occurs when replacing circuit boards. |
 | 308 | 회로 board에 아웃리거 사양 미설정Outrigger specifications not specified on circuit board Occurs when replacing circuit boards. |
 | 409 | EEPROM 오작동EEPROM malfunction Displayed when read/write from/to EEPROM fails. |
 | 310 | 주 및 디스플레이 유닛 통신 에러Main and display units communication error Main unit and display unit cannot communicate. |
 | 313 | 소프트웨어 코드 불일치Software code mismatch Software codes for the main and display units do not match. |
 | 314 | 크레인 기종 및 소프트웨어 코드 내 EEPROM이(가) 크레인 기종 및 소프트웨어 코드 내 program와 불일치The crane model and software code in the EEPROM do not match the crane model and software code in the program. |
 | 420 | ACS-COR 통신 에러ACS-COR communication error |
 | 421 | CORDT-FT 통신 에러CORDT-FT communication error |
 | 422 | 우-전방 아웃리거 스트로크 단선 또는 단락Broken or short circuit in right-front outrigger stroke |
 | 423 | 우-후방 아웃리거 스트로크 단선 또는 단락Broken or short circuit in right-rear outrigger stroke |
 | 424 | 좌-후방 아웃리거 스트로크 단선 또는 단락Broken or short circuit in left-rear outrigger stroke |
 | 425 | 좌-전방 아웃리거 스트로크 단선 또는 단락Broken or short circuit in left-front outrigger stroke |
 | 426 | 엔진 RPM 센서 에러Engine RPM sensor error |
 | 429 | 아웃리거 조정 에러Outrigger adjustment error Occurs when an outrigger fully retracted value is same as fully extended value or fully extended value is smaller, etc. |
 | 333 | 본체 CPU 주소 에러Main unit CPU address error 주소 에러 발생 본체 내 CPU일 때 표시됨 · If this occurs, the crane automatically stops, then the CPU stops functioning. |
 | 334 | 본체 CPU 미정의 에러 코드 1Main unit CPU undefined error code 1 An undefined code 1 was executed in the main unit CPU. If this occurs, the crane automatically stops, then the CPU stops functioning. |
 | 335 | 본체 CPU 미정의 에러 코드 2Main unit CPU undefined error code 2 An undefined code 2 was executed in the main unit CPU. If this occurs, the crane automatically stops, then the CPU stops functioning. |
 | 340 | 붐 길이 센서 단선 또는 단락Broken or short circuit in boom length sensor |
 | 440 | 붐 완전 축소 길이 오차Boom full retraction length error Displayed when there is a large amount of length error when the boom is fully retracted. · 완전 축소 길이 가능 수동 조정. · If this adjustment has been made, contact your authorized KATO dealer. |
 | 441 | 붐 길이 오프셋 조정값 에러Boom length offset adjustment value error [붐 길이 오프셋 조정값 < -(47m -(최대 길이 · 최소 길이)] 용 KA-1300RX, 이 에러는 다음일 때 발생 — 조정값 미만 -6.8m. |
 | 443 | 붐 길이 조정값 에러Boom length adjustment value error [붐 길이 영점 조정값 < -(47m -(최대 길이 · 최소 길이)] 용 KA-1300RX, 이 에러는 다음일 때 발생 — 조정값 미만 -6.8m. |
 | 447 | 지브 커넥터 에러Jib connector error Displayed when the boom status is set to boom or rooster sheave operation and the jib angle sensor connector is connected, indicating a faulty connector, or when the boom status is set to jib or boom with the jib operation and the jib connector is not connected. |
 | 350 | 붐 각도 단선 또는 단락Broken or short circuit in boom angle |
 | 351 | 탑(선단) 각도 센서 단선 또는 단락Broken or short circuit in top angle sensor |
 | 451 | 탑(선단) 각도 센서 단선 또는 단락Broken or short circuit in top angle sensor |
 | 452 | 탑(선단) 각도 오차Top angle error If the difference between the top angle and boom angle is more than 10 degrees, check each sensor. |
 | 355 | 지브 각도 검출기 단선 또는 단락Broken or short circuit in the jib angle detector |
 | 357 | 지브 길이 검출기 단선 또는 단락Broken or short circuit in the jib length detector |
 | 458 | 지브 길이 오프셋 조정값 에러Jib length offset adjustment value error [지브 길이 오프셋 조정값 용 KA-1300RX, 이 에러는 다음일 때 발생 — 조정값 미만 -5.1 m. |
 | 360 | 기복 센서 에러Derrick sensor error Derrick pressure sensor P1 or P2 malfunctioned. |
 | 361 | 기복 압력 센서 P1 단선 또는 단락Broken or short circuit in derrick pressure sensor P1 |
 | 362 | SL 지브 기복 압력 센서 에러SL jib derrick pressure sensor error SL 지브 기복 압력 센서 P1 또는 P2 불량 |
 | 363 | SL 지브 기복 압력 센서 P1 단선 또는 단락Broken or short circuit in SL jib derrick pressure sensor P1 |
 | 364 | 주 윈치 회전 고착 에러 where rotates 내 하강 방향 임에도 주 윈치 레버 조작됨 내 권상 방향Main winch rotation sticking error where it rotates in the lowering direction even though the main winch lever is operated in the hoisting direction |
 | 365 | 주 윈치 회전 고착 에러 where rotates 내 권상 방향 임에도 주 윈치 레버 조작됨 내 하강 방향Main winch rotation sticking error where it rotates in the hoisting direction even though the main winch lever is operated in the lowering direction |
 | 366 | 주 윈치 회전 고착 에러 where rotates 내 권상 방향 임에도 주 윈치 레버 내 중립 위치Main winch rotation sticking error where it rotates in the hoisting direction even though the main winch lever is in the neutral position |
 | 367 | 보조 윈치 회전 고착 에러 where rotates 내 하강 방향 임에도 보조 윈치 레버 조작됨 내 권상 방향Auxiliary winch rotation sticking error where it rotates in the lowering direction even though the auxiliary winch lever is operated in the hoisting direction |
 | 368 | 보조 윈치 회전 고착 에러 where rotates 내 권상 방향 임에도 보조 윈치 레버 조작됨 내 하강 방향Auxiliary winch rotation sticking error where it rotates in the hoisting direction even though the auxiliary winch lever is operated in the lowering direction |
 | 369 | 보조 윈치 회전 고착 에러 where rotates 내 권상 방향 임에도 보조 윈치 레버 내 중립 위치Auxiliary winch rotation sticking error where it rotates in the hoisting direction even though the auxiliary winch lever is in the neutral position |
 | 371 | 기복 압력 센서 P2 단선 또는 단락Broken or short circuit in derrick pressure sensor P2 |
 | 372 | SL 지브 기복 압력 센서 P2 단선 또는 단락Broken or short circuit in SL jib derrick pressure sensor P2 |
 | 373 | 주 윈치 회전 고착 에러 where rotates 내 하강 방향 임에도 주 윈치 레버 내 중립 위치Main winch rotation sticking error where it rotates in the lowering direction even though the main winch lever is in the neutral position |
 | 374 | 보조 윈치 회전 고착 에러 where rotates 내 하강 방향 임에도 보조 윈치 레버 내 중립 위치Auxiliary winch rotation sticking error where it rotates in the lowering direction even though the auxiliary winch lever is in the neutral position |
 | 376 | 붐 신장/축소 조작 레버 고착 에러Boom extension/retraction control lever sticking error Displayed when the boom length changes even though the boom extension/retraction control lever is not being operated or the boom length changes in the opposition direction of the control lever operation. |
 | 377 | 지브 기복/하강 조작 레버 고착 에러Jib derricking/lowering control lever sticking error Displayed when the jib derricking/lowering position changes even though the jib derricking/lowering control lever is not being operated or it changes in the opposition direction of the control lever operation. |
 | 378 | 지브 신장/축소 조작 레버 고착 에러Jib extension/retraction control lever sticking error Displayed when the jib length changes even though the jib extension/retraction control lever is not being operated or the jib length changes in the opposition direction of the control lever operation. |
 | 380 | 끊김 회로 내 선회 각도 센서Broken circuit in slewing angle sensor |
 | 381 | 끊김 회로 내 선회 엔코더 신호Broken circuit in slewing encoder signal A |
 | 382 | 끊김 회로 내 선회 엔코더 신호 BBroken circuit in slewing encoder signal B |
 | 387 | 선회 후방 스위치 에러Slewing rear switch error |
 | 388 | 선회 영점 조정 스위치 에러Slewing zero adjustment switch error |
 | 390 | 개방 탑(선단) 단자 통신 회로Open top terminal communication circuit |
 | 490 | 개방 탑(선단) 단자 통신 회로Open top terminal communication circuit |
 | 391 | 통신 에러 와(과) 탑(선단) 단자Communication error with top terminal |
 | 491 | 통신 에러 와(과) 탑(선단) 단자Communication error with top terminal |
 | 495 | 크레인 시리얼 없음. · 아님 지정됨 내 EEPROMCrane serial No. not specified in EEPROM |
 | 496 | 본체 시간 읽기 에러Main unit time reading error 불가 읽기 본체 시간. |
 | 497 | 배터리 전압 20V 이하Battery voltage is 20V or less |
 | 498 | 백업 전원 배선 에러Backup power supply wiring error 백업 전원 공급전압 5V 이하, 원인 — 단선 또는 단락. · 배터리 전압 및 배선 점검 |
 | 499 | 과부하 데이터 메모리 영역 완전Overload data memory area is full No or minimal memory space is available, because more than the specified number of overload data values were recorded. |
 | 201 | 모멘트 정지Moment stop Displayed when the operation stops automatically after comparing current and limit loads during operations such as lowering or extending the boom, winding up the winch, or lowering the jib. |
 | 203 | 붐 상한 각도 정지Boom upper limit angle stop Displayed when a boom derricking stop angle is specified and the operation stops automatically after the boom angle reaches that angle. |
 | 204 | 붐 상한 각도 정지 경고Boom upper limit angle stop warning Displayed when a boom derricking stop angle is specified and the intermittent sound alarm "DING DONG, DING DONG" is output after the boom angle is -2 degrees or less from that stop angle. |
 | 205 | 붐 하한 각도 정지Boom lower limit angle stop Displayed when a boom lowering stop angle is specified and the operation stops automatically after the boom angle reaches that angle. |
 | 206 | 붐 하한 각도 정지 경고Boom lower limit angle stop warning Displayed when a boom lowering stop angle is specified and the intermittent sound alarm "DING DONG, DING DONG" is output after the boom angle is +2 degrees or less from that stop angle. |
 | 207 | 우 선회 정지Right slewing stop Displayed when slewing right and the operation stops after becoming dangerous. |
 | 208 | 우 선회 정지 경고Right slewing stop warning Displayed when slewing right and a warning is output after reaching 5 degrees from the stop position. |
 | 209 | 좌 선회 정지Left slewing stop Displayed when slewing left and the operation stops after becoming dangerous. |
 | 210 | 좌 선회 정지 경고Left slewing stop warning Displayed when slewing left and a warning is output after reaching 5 degrees from the stop position. |
 | 211 | 하부 각도 한계 정지Lower angle limit stop Displayed when a lower angle limit is specified and the operation stops automatically after the boom angle reaches that limit value. |
 | 212 | 하부 각도 한계 정지 경고Lower angle limit stop warning Displayed when a lower angle limit is specified and the intermittent sound alarm "DING DONG", "DING DONG" is output after the boom angle reaches +2 degrees or less from that limit value. |
 | 213 | 상부 각도 한계 정지Upper angle limit stop Displayed when an upper angle limit is specified and the operation stops automatically after the boom angle reaches that limit value. |
 | 214 | 상부 각도 한계 정지 경고Upper angle limit stop warning Displayed when an upper angle limit is specified and the intermittent sound alarm "DING DONG", "DING DONG" is output after the boom angle reaches -2 degrees or less from that limit value. |
 | 215 | 작업반경 한계 정지Radius limit stop Displayed when a radius limit is specified and the operation stops automatically after reaching that radius limit. |
 | 216 | 작업반경 한계 정지 경고Radius limit stop warning Displayed when a radius limit is specified and the intermittent sound alarm "DING DONG", "DING DONG" is output after the radius reaches -50cm or less from that limit value. |
 | 217 | 최대 권상 높이 한계 정지Maximum hoist height limit stop Displayed when a maximum hoist height limit is specified and the operation stops automatically after reaching that height limit. |
 | 218 | 최대 권상 높이 한계 정지 경고Maximum hoist height limit stop warning Displayed when a maximum hoist height limit is specified and the intermittent sound alarm "DING DONG", "DING DONG" is output after reaching -50 cm from that hoist height limit. |
 | 219 | 우 선회 한계 정지Right slewing limit stop Displayed when a right slewing limit value is specified and right slewing stops automatically after the slewing angle reaches that limit value. |
 | 220 | 우 선회 한계 정지 경고Right slewing limit stop warning Displayed when a right slewing limit value is specified and the intermittent sound alarm "DING DONG, DING DONG" is output after the slewing angle reaches · 5 도 이하 에서 한계값. |
 | 221 | 좌 선회 한계 정지Left slewing limit stop Displayed when a left slewing limit value is specified and left slewing stops automatically after the slewing angle reaches that limit value. |
 | 222 | 좌 선회 한계 정지 경고Left slewing limit stop warning Displayed when a left slewing limit value is specified and the intermittent sound alarm "DING DONG, DING DONG" is output after the slewing angle reaches · 5 도 이하 에서 한계값. |
 | 223 | 자동정지 의 전체 동작Auto-stop of all operations Displayed when all operations stop automatically. |
 | 225 | 에러 자동정지Error auto-stop Displayed when an operation stops automatically after an error occurs. Auto-stop does not occur for Fxx errors. |
 | 226 | 에러 경고Error warning Displayed when the intermittent sound alarm "DING DONG DING DONG" is output after an error occurs. |
 | 228 | 레버 stand 격납 경고Lever stand stowage warning Displayed when a control lever is operated with the lever stand stowed. "DING DONG. Set the lever stand." is emitted. |
 | 229 | 배선 당김 정지Line pull stop Displayed when an operation stops automatically after the line pull force (actual load/number of parts of line) exceeds the allowable line pull force. |
 | 230 | 배선 당김 정지 경고Line pull stop warning Displayed when the intermittent sound alarm "DING DONG", "DING DONG" is output after the line pull force (actual load/number of parts of line) exceeds the allowable line pull force. |
 | 231 | 최대 붐 각도 정지Maximum boom angle stop Displayed when an operation stops automatically after the boom reaches the specified maximum angle. |
 | 232 | 최대 지브 각도 정지Maximum jib angle stop Displayed when the jib angle reaches the maximum jib angle setting and the jib stops automatically. |
 | 233 | 정지 원인 — 단선 커넥터 용 confirming 지브 연결Stopped due to disconnected connector for confirming jib connection Displayed when a jib control lever is operated and the operation is automatically stopped because the connector for the jib angle detector is not connected to the top terminal. |
 | 234 | Special 최대 지브 각도 정지Special maximum jib angle stop Displayed when the jib angle reaches the special maximum jib angle setting and the jib stops automatically. · The maximum angle changes to the range of 2 to 5 degrees when the SL jib length is in the range of 9.2 to 15.0 meters. · 지브 할 수 없음 상승됨 또는 축소. |
 | 235 | 지브 완전 하강 정지Jib fully-lowered stop Displayed when the jib angle reaches the preset fully-lowered angle and the jib stops automatically. |
 | 236 | 지브 완전 하강 정지 경고Jib fully-lowered stop warning Displayed when the intermittent sound alarm "DING DONG", "DING DONG" is output after the jib reaches +2 degrees or less from the preset fully-lowered angle. |
 | 239 | 기복 lowered 끝 정지Derrick lowered end stop Displayed when the boom has been lowered to the cylinder end and an operation to lower the boom, extend the boom, or wind up the winch is automatically stopped. |
 | 243 | 목표 1 partially 이내 범위Target 1 partially within range Displayed when either the slewing angle or radius of the target 1 is within the specified range (±1.5 m radius or ±7.5 degrees slewing angle). |
 | 244 | 목표 1 이내 범위Target 1 within range 양쪽 선회 각도 및 작업반경 의 목표 1 이내 지정됨 범위 (±1.5 m 작업반경 및 ±7.5 도 선회 각도)일 때 표시됨 |
 | 245 | 목표 2 partially 이내 범위Target 2 partially within range Displayed when either the slewing angle or radius of the target 2 is within the specified range (±1.5 m radius or ±7.5 degrees slewing angle). |
 | 246 | 목표 2 이내 범위Target 2 within range 양쪽 선회 각도 및 작업반경 의 목표 2 이내 지정됨 범위 (±1.5 m 작업반경 및 ±7.5 도 선회 각도)일 때 표시됨 |
 | 248 | SL 지브 완전축소 스위치 검출됨SL jib full retraction switch detected Displayed when the SL jib full retraction switch is detected. |
 | 249 | 선회 soft 정지 출력Slewing soft stop output Displayed when a slewing soft stop is output. |
 | 251 | 외부 메모리 장치 전원 OFFExternal memory device power is OFF Displayed when the power supply for an external memory device is attached to the ACS and the power for the external memory device is OFF. |
 | 252 | 메모리 카드 삽입됨 내 외부 메모리 장치 없음No memory card is inserted in external memory device Displayed when an external memory device is attached to the ACS and a memory card is not inserted in the external memory device. |
 | 253 | 자동정지 용 고착 윈치 조작 레버Auto-stop for sticking winch control lever Displayed when the operation stops automatically due to the winch rotating when the winch is not being operated and the winch valve spool is presumed to be stuck. The PTO or power supply must be shut OFF to cancel this icon. |
 | 254 | 자동 전(全)정지 의 붐 하강 레버Auto all-stop of boom lowering lever Displayed when all other operations stop automatically due to the boom derricking/lowering lever being in the lowering position. |
 | 255 | 자동 전(全)정지 의 붐 기복 레버Auto all-stop of boom derricking lever Displayed when all other operations stop automatically due to the boom derricking/lowering lever being in the derricking position. |
 | 256 | 자동 전(全)정지 의 붐 신장 레버Auto all-stop of boom extension lever Displayed when all other operations stop automatically due to the boom extension/retraction lever or pedal being in the extension position. |
 | 257 | 자동 전(全)정지 의 붐 축소 레버Auto all-stop of boom retraction lever Displayed when all other operations stop automatically due to the boom extension/retraction lever or pedal being in the retraction position. |
 | 258 | 자동 전(全)정지 의 주 윈치 권상 레버Auto all-stop of main winch hoisting lever Displayed when all other operations stop automatically due to the main winch lever or pedal being in the hoisting position. |
 | 259 | 자동 전(全)정지 의 주 윈치 하강 레버Auto all-stop of main winch lowering lever Displayed when all other operations stop automatically due to the main winch lever or pedal being in the lowering position. |
 | 260 | 자동 전(全)정지 의 보조 윈치 권상 레버Auto all-stop of auxiliary winch hoisting lever Displayed when all other operations stop automatically due to the auxiliary winch lever or pedal being in the hoisting position. |
 | 261 | 자동 전(全)정지 의 보조 윈치 하강 레버Auto all-stop of auxiliary winch lowering lever Displayed when all other operations stop automatically due to the auxiliary winch lever or pedal being in the lowering position. |
 | 262 | 자동 전(全)정지 원인 — 지브 기복/축소 레버Auto all-stop due to jib derricking/retraction lever Displayed when all other operations stop automatically due to the SL jib derricking/lowering lever being in the derricking position or the SL jib extension/retraction lever being in the retraction position. |
 | 263 | 자동 전(全)정지 원인 — 지브 하강/신장 레버Auto all-stop due to jib lowering/extension lever Displayed when all other operations stop automatically due to the SL jib derricking/lowering lever being in the lowering position or the SL jib extension/retraction lever being in the extension position. |
 | 264 | 자동 전(全)정지 의 선회 레버 우측Auto all-stop of slewing lever to rightward Displayed when all other operations stop automatically due to the slewing lever being in the right side. |
 | 265 | 자동 전(全)정지 의 선회 레버 좌측Auto all-stop of slewing lever to leftward Displayed when all other operations stop automatically due to the slewing lever being in the left side. |
 | 269 | 외부 메모리 장치 에러External memory device error Displayed when an external memory device is attached to the ACS and an error occurs in that memory device. |
 | 270 | 선회 브레이크 출력 디스플레이Slewing brake output display Displayed when a slewing brake is output. |
 | 271 | 작업 영역 한계 정지Working area limit stop Displayed when an auto-stop occurs due to a working area limit. |
 | 272 | 작업 영역 한계 정지 경고Working area limit stop warning Displayed when the slewing angle is within 5 degrees from the working area limit stop angle or the working radius is within 50 cm from the working area limit stop radius. · 간헐적 소리 경보 "DING DONG", "DING DONG" 출력. |
 | 278 | 자동정지 에 의해 ACS 비상 스위치 작동Auto-stop by ACS emergency switch operation Displayed when the load rate has exceeded 100% in ACS emergency switch operation and the auto-stop function is activated. |
 | 279 | 자동정지Auto-stop |
 | 283 | 카운터웨이트 변경 경고Counterweight change warning This warning is displayed for a few seconds when a change in counterweight detection has occurred. When the warning goes off, the counterweight will change. |
 | 284 | |
 | 285 | 주 훅 양중 높이 범위Main hook lifting height range Displayed when the main hook lifting height has approached the lifting height target, maximum lifting height or ground level. |
 | 286 | 주 훅 양중 높이 조정 경고Main hook lifting height adjustment warning Displayed when it is determined that the main hook lifting height needs adjustment. |
 | 287 | 주 훅 와이어로프 한계 경고Main hook rope limit warning Displayed when the rope cannot be payed out from the main drum any more. |
 | 288 | 보조 훅 양중 높이 범위Auxiliary hook lifting height range Displayed when the auxiliary hook lifting height has approached the lifting height target, maximum lifting height or ground level. |
 | 289 | 보조 훅 양중 높이 조정 경고Auxiliary hook lifting height adjustment warning Displayed when it is determined that the auxiliary hook lifting height needs adjustment. |
 | 290 | 보조 훅 와이어로프 한계 경고Auxiliary hook rope limit warning Displayed when the rope cannot be payed out from the auxiliary drum any more. |
 | 291 | 2-telescopic 실린더-차단 출력 디스플레이2-telescopic cylinder-shutoff output display When 2-telescopic cylinder-shutoff is being output. |
 | 292 | SL 지브 하중 정지SL jib load stop Auto-stop function that is activated when a load is hoisted with the SL jib hook with the boom status set to boom operation with the jib. · 변경 작업 상태 → SL 지브 작동. |
 | 293 | 완전 축소 상태 지브 길이 조정됨Fully retracted jib length adjusted Indicates that the automatic jib length adjustment function, on cranes with the function specified, has adjusted the jib length to the fully retracted length. |
 | 294 | 주 하중 정지Main load stop Auto-stop function that is activated when a load is hoisted with the main hook with the boom status set to SL jib mode. · 변경 작업 상태 → 붐 작동 와(과) 지브. |
 | 295 | 조정됨 붐 → 완전 축소 상태 길이Adjusted boom to fully retracted length 표시 붐 길이 조정됨 → 완전 축소 상태 길이. · It is displayed when the boom is retracted to its fully retracted length using only the boom retraction operation starting before the boom is fully retracted, the fully retracted length is confirmed, and the length is adjusted. |
 | 296 | 자동정지 에 의해 ACS 비상 스위치 금지됨Auto-stop by ACS emergency switch disabled 자동정지 에 의해 ACS 비상 스위치 아님 작동됨 시 하중 비율 초과 100%일 때 표시됨 |
 | 297 | 크레인 기록 정지Crane record stopped Displayed when the crane operation log is stopped. This also changes the movement indicator(* ) from flashing green and red to flashing blue and red. |
 | 299 | 과부하 이벤트 기록됨Overload event recorded Displayed when an overload event is recorded. |
 | 756 | 붐 신장 조작 레버 에러Boom extension control lever error Displayed when the boom extension lever switch is turned ON when the boom is retracting. · (내 경우 의 동시 입력 에서 붐 신장/축소 레버) |
 | 757 | 붐 축소 조작 레버 에러Boom retraction control lever error Displayed when the boom retraction lever switch is turned ON when the boom is extending. · (내 경우 의 동시 입력 에서 붐 신장/축소 레버) |
 | 758 | 주 윈치 권상 조작 레버 에러Main winch hoisting control lever error Displayed when the main winch hoisting control lever switch is turned ON when the main winch is winding down. · (내 경우 의 동시 입력 에서 주 윈치 권상/하강 레버) |
 | 759 | 주 윈치 하강 조작 레버 에러Main winch lowering control lever error Displayed when the main winch lowering control lever switch is turned ON when the main winch is winding up. · (내 경우 의 동시 입력 에서 주 윈치 권상/하강 레버) |
 | 760 | 보조 윈치 권상 조작 레버 에러Auxiliary winch hoisting control lever error Displayed when the auxiliary winch hoisting control lever switch is turned ON when the auxiliary winch is winding down. · (내 경우 의 동시 입력 에서 보조 윈치 권상/하강 레버) |
 | 761 | 보조 윈치 하강 조작 레버 에러Auxiliary winch lowering control lever error Displayed when the auxiliary winch lowering control lever switch is turned ON when the auxiliary winch is winding up. · (내 경우 의 동시 입력 에서 보조 윈치 권상/하강 레버) |
 | 762 | 지브 기복 조작 레버 에러Jib derricking control lever error Displayed when the jib derricking control lever switch is turned ON when the jib is lowering. · (내 경우 의 동시 입력 에서 지브 기복/하강 레버) |
 | 763 | 지브 하강 조작 레버 에러Jib lowering control lever error Displayed when the jib lowering control lever switch is turned ON when the jib is derricking. · (내 경우 의 동시 입력 에서 지브 기복/하강 레버) |
 | 764 | 지브 신장 조작 레버 에러Jib extension control lever error Displayed when the jib extension control lever switch is turned ON when the jib is retracting. · (내 경우 의 동시 입력 에서 지브 신장/축소 레버) |
 | 765 | 지브 축소 조작 레버 에러Jib retraction control lever error Displayed when the jib retraction control lever switch is turned ON when the jib is extending. · (내 경우 의 동시 입력 에서 지브 신장/축소 레버) |
 | 842 | 범위 한계 설정/취소 에러Range limit set/cancel error Displayed when a working range limit setting is entered or canceled while a control lever is being operated. If this occurs, the range limit is not set or canceled. This icon will switch off after 3 seconds. |
 | 237 | 수평 붐 정지Horizontal boom stop Displayed when a horizontal boom stop is specified and the boom stops automatically after the boom angle reaches zero degrees. |
 | 242 | 훅 격납 경고Hook stowage warning Displayed when a warning is output because a crane for which the hook stowage control is specified gets to the hook stowage status. |
 | 247 | 붐 soft 정지 출력Boom soft stop output Displayed when the boom soft stop switch is ON and a boom soft stop is output. |
| 248 | 붐 하강 접점 정지Boom lowering contact stop Displayed when the boom lowering stop angle is specified depending on the slewing angle and the operation stops after the boom angle reaches that limit angle. |
| 270 | 자동정지Auto-stop |
 | 273 | 작업 영역 한계 CD 정지Working area limit CD stop 자동정지 발생 원인 — 작업 영역 한계 CD일 때 표시됨 |
 | 274 | 작업 영역 한계 CD 경고Working area limit CD warning Displayed when the slewing angle is within 5 degrees from the working area limit CD stop angle or the working radius is within 50 cm from the working area limit CD stop radius. · 간헐적 소리 경보 "DING DONG", "DING DONG" 출력. |
 | 276 | 지브 격납 pin 경고Jib stowage pin warning This warning is output when the main or rooster mode is selected without the jib foot pins being inserted properly. |
| 284 | 지브 상부 각도 proximity 경고Jib upper angle proximity warning Displayed during jib upper angle soft stop control. When the boom soft stop is OFF, this is displayed from 10 degrees before the jib upper angle. |
| 285 | 지브 fully 상승됨 및 정지Jib fully raised and stops Displayed when the jib is fully raised and stops |
| 286 | 과권상 정지 취소Overhoisting stop cancel 과권상 정지 않음 발생, e.g일 때 표시됨 · 시 지브 설정. |
| 289 | 하중 factor 한계 정지Load factor limit stop Displayed when an auto-stop occurs due to load factor limit. |
| 290 | 하중 factor 한계 정지 경고Load factor limit stop warning Displayed when the load factor is within 5% of the stop load factor due to load factor limit. · 간헐적 소리 경보 "DING DONG", "DING DONG" 출력. |
| 291 | 자동정지 에 의해 ACS 비상 스위치 작동Auto-stop by ACS emergency switch operation 자동정지 에 의해 ACS 비상 스위치 작동 작동됨 시 하중 비율 초과 100%일 때 표시됨 |
| 292 | 해제 의 자동정지 에 의해 ACS 비상 스위치 작동Release of auto-stop by ACS emergency switch operation 자동정지 에 의해 ACS 비상 스위치 작동 아님 작동됨 시 하중 비율 초과 100%일 때 표시됨 |
| 294 | 조정됨 붐 → 완전 신장 상태 길이Adjusted boom to fully extended length 표시 붐 됨 완전 신장 상태 → 최대 길이. · Displayed when, before the boom is fully extended, the boom is extended using only the boom extending operation and the boom length is adjusted when confirming the boom has stopped at the fully extended position. |
| 295 | 조정됨 붐 → 완전 축소 상태 길이Adjusted boom to fully retracted length 표시 붐 됨 완전 축소 상태 → 최소 길이. · Displayed when, before the boom is fully retracted, the boom is retracted using only the boom retracting operation and the boom length is adjusted when confirming the boom has stopped at the fully retracted position. |
 | 749 | 하강 motion 한계 정지Lowering motion limit stop Displayed when a lever is operated when the lowering motion limit has been reached. |
 | 750 | 하강 motion 한계 경보Lowering motion limit alarm Displayed when the lowering motion limit has been reached. |
 | 767 | 지브 하강 정지Jib lowering stop Displayed when an automatic stop occurs because the jib derricking/lowering lever is in the lowering position. |
 | 769 | 붐 신장 정지Boom extension stop Displayed when auto-stop occurs because the boom extension/retraction lever is in the extension position. |
 | 771 | 붐 축소 정지Boom retraction stop Displayed when auto-stop occurs because the boom extension/retraction lever is in the retraction position. |
 | 773 | 지브 신장 정지Jib extension stop Displayed when auto-stop occurs because the jib extension/retraction lever is in the extension position. |
 | 774 | 지브 축소 정지Jib retraction stop Displayed when auto-stop occurs because the jib extension/retraction lever is in the retraction position. |
 | 778 | 지브 기복 정지Jib derricking stop Displayed when auto-stop occurs because the jib derricking/lowering lever is in the derricking position. |
 | 779 | 주 권취 정지Main winding stop Displayed when an auto-stop of the winding occurs because the main winch lever is in the winding position. |
 | 793 | 저속 작동 모드Slow operating mode 아이콘 표시됨 중 동작 저속 모드에서. · (including the time of preoperational checks) |
 | 866 | 저속 작동 모드Slow operating mode 아이콘 표시됨 중 동작 저속 모드에서. · (including the time of preoperational checks) |
| 866 | 자동정지 의 붐 하강 중 탐색기 훅 동작Auto-stop of boom lowering during searcher hook operations Displayed when an auto-stop occurs due to boom lowering lever operations performed during searcher hook operations. |
 | 867 | 자동정지 의 붐 raising 중 탐색기 훅 동작Auto-stop of boom raising during searcher hook operations Displayed when an auto-stop occurs due to boom raising lever operations performed during searcher hook operations. |
 | 868 | 자동정지 의 붐 신장 중 탐색기 훅 동작Auto-stop of boom extension during searcher hook operations Displayed when an auto-stop occurs due to boom extension lever operations performed during searcher hook operations. |
 | 876 | 비상 우-선회 정지Emergency right-slew stop 표시됨 시 ACS 비상 동작 금지됨 원인 — 선회 으로 우 중 ACS 비상 동작. · (참조 "ACS 비상 동작".) |
 | 877 | 비상 좌-선회 정지Emergency left-slew stop 표시됨 시 ACS 비상 동작 금지됨 원인 — 선회 으로 좌 중 ACS 비상 동작. · (참조 "ACS 비상 동작".) |
 | 878 | 보조 윈치 정지 2Auxiliary winch stop 2 Displayed if the auxiliary winch is operated when operating the searcher hook or the boom with the searcher hook attached. · 자동으로 정지 작동. |
 | 879 | 비상 크레인 동작Emergency crane operations Displayed when the emergency operating device is used. |
 | 880 | 붐 하강 접점 경고Boom lowering contact warning Displayed when the boom lowering stop angle is specified depending on the slewing angle and the boom angle reaches +2 degrees from that limit angle. |
 | 881 | 우 선회 접점 정지Right slewing contact stop Displayed when the right slewing stop angle is specified depending on the boom angle and the slewing angle reaches that limit angle. |
 | 882 | 우 선회 접점 경고Right slewing contact warning Displayed when the right slewing stop angle is specified depending on the boom angle and the slewing angle reaches -5 degrees from that limit angle. |
 | 883 | 좌 선회 접점 정지Left slewing contact stop Displayed when the left slewing stop angle is specified depending on the boom angle and the slewing angle reaches that limit angle. |
 | 884 | 좌 선회 접점 경고Left slewing contact warning Displayed when the left slewing stop angle is specified depending on the boom angle and the slewing angle reaches +5 degrees from that limit angle. |
 | 885 | 붐 하강 경고 중 탐색기 훅 동작Boom lowering warning during searcher hook operations Displayed when an auto-stop occurs due to boom lowering lever operations performed during searcher hook operations and then the lever is returned to the neutral position. When the icon is displayed, the operation stops automatically when the specified lever is operated. |
 | 886 | 붐 raising 경고 중 탐색기 훅 동작Boom raising warning during searcher hook operations Displayed when an auto-stop occurs due to boom raising lever operations performed during searcher hook operations and then the lever is returned to the neutral position. When the icon is displayed, the operation stops automatically when the specified lever is operated. |
 | 887 | 붐 신장 경고 중 탐색기 훅 동작Boom extension warning during searcher hook operations Displayed when an auto-stop occurs due to boom extension lever operations performed during searcher hook operations and then the lever is returned to the neutral position. When the icon is displayed, the operation stops automatically when the specified lever is operated. |
 | 1230 | 아웃리거 축소 작동Outrigger retraction operation Displayed when only outrigger retraction operation is selected. |
 | 1231 | 수평 축소 작동Horizontal retraction operation Displayed when a horizontal cylinder or retraction operation is selected. |
 | 1232 | 수직 축소 작동Vertical retraction operation Displayed when a vertical cylinder or retraction operation is selected. |
 | 1233 | 아웃리거 신장 작동Outrigger extension operation Displayed when only outrigger extension operation is selected. |
 | 1235 | 수직 신장 작동Vertical extension operation splayed when a vertical cylinder or extension operation is selected. |
 | 1236 | 수평 작동Horizontal operation Displayed when only horizontal cylinder operation is selected. |
 | 1237 | 수직 작동Vertical operation Displayed when only vertical cylinder operation is selected. |
 | 1243 | 아웃리거 신장/축소 작동 에러Outrigger extension/retraction operation error Displayed when there is an abnormality in the signal for extension or retraction operation. |
 | 1244 | 수평/수직 작동 에러Horizontal/vertical operation error Displayed when there is an abnormality in the signal for horizontal or vertical operation. |
 | 442 | 완전축소 스위치 고착 에러Full retraction switch stuck error |
 | 484 | 선회 포텐쇼미터 단선 또는 단락Broken or short circuit in slewing potentiometer |
 | 485 | 선회 포텐쇼미터 기준 지점 고장Slewing potentiometer reference point failure |
 | 486 | 선회 포텐쇼미터 전압 고장Slewing potentiometer voltage failure |
 | 489 | 선회 엔코더 및 포텐쇼미터 angles 불일치.Slewing encoder and potentiometer angles are inconsistent. |
 | 241 | 훅 격납 자동정지Hook stowage auto-stop Displayed when auto-stop is output in the hook stowage status on a crane for which the hook stowage control is specified. |
 | 267 | 시트 스위치 정지Seat switch stop Displayed when a lever operation is attempted without the operator sitting in the seat and the operation stops. |
 | 277 | 자동정지 용 prevention → 단선 지브 격납 브래킷Auto-stop for prevention to break the jib stowage bracket Displayed when the boom length is below +0.5m from min. · 길이, 붐 각도 10 도, 이상 및 지브 격납 링크 스위치 회전됨 OFF 와(과) 지브 설정 모드. · Appeared when telescopic extension is operated. |
 | 280 | 지브 drawing/해제 허용됨 상태Jib drawing/release enabled status Displayed when the boom length is below +0.2m from min. · 길이, 붐 각도 이내 55 → 65 도, 및 지브 격납 링크 스위치 회전됨 ON 와(과) 지브 설정 모드. |
 | 281 | 지브 격납 링크 경고Jib stowage link warning Displayed when the boom length is below +0.2m from min. · 길이, 붐 각도 이내 10 → 35 도, 및 지브 격납 링크 스위치 회전됨 ON 와(과) 지브 설정 모드. |
 | 768 | Releasing 지브 기복 압력 상태Releasing Jib derricking pressure status Displayed when the pilot pressure of jib derricking is released. |
크레인사업자협동조합